Import Upstream version 5.4.13

Documentation/ABI/stable/sysfs-driver-mlxreg-io

@@ -29,13 +29,13 @@ Description:	This file shows the system fans direction:
 
 		The files are read only.
 
-What:		/sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/jtag_enable
+What:		/sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld3_version
 
 Date:		November 2018
 KernelVersion:	5.0
 Contact:	Vadim Pasternak <vadimpmellanox.com>
 Description:	These files show with which CPLD versions have been burned
-		on LED board.
+		on LED or Gearbox board.
 
 		The files are read only.
 
@@ -121,6 +121,15 @@ Description:	These files show the system reset cause, as following: ComEx
 
 		The files are read only.
 
+What:		/sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/cpld4_version
+Date:		November 2018
+KernelVersion:	5.0
+Contact:	Vadim Pasternak <vadimpmellanox.com>
+Description:	These files show with which CPLD versions have been burned
+		on LED board.
+
+		The files are read only.
+
 Date:		June 2019
 KernelVersion:	5.3
 Contact:	Vadim Pasternak <vadimpmellanox.com>

Documentation/ABI/testing/sysfs-bus-mei

@@ -4,7 +4,7 @@ KernelVersion:	3.10
 Contact:	Samuel Ortiz <sameo@linux.intel.com>
 		linux-mei@linux.intel.com
 Description:	Stores the same MODALIAS value emitted by uevent
-		Format: mei:<mei device name>:<device uuid>:
+		Format: mei:<mei device name>:<device uuid>:<protocol version>
 
 What:		/sys/bus/mei/devices/.../name
 Date:		May 2015

Documentation/admin-guide/device-mapper/index.rst

@@ -8,6 +8,7 @@ Device Mapper
     cache-policies
     cache
     delay
+    dm-clone
     dm-crypt
     dm-flakey
     dm-init

Documentation/admin-guide/kernel-parameters.txt

@@ -113,7 +113,7 @@
 			the GPE dispatcher.
 			This facility can be used to prevent such uncontrolled
 			GPE floodings.
-			Format: <int>
+			Format: <byte>
 
 	acpi_no_auto_serialize	[HW,ACPI]
 			Disable auto-serialization of AML methods

Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt

@@ -46,7 +46,7 @@ Required properties:
 Example (R-Car H3):
 
 	usb2_clksel: clock-controller@e6590630 {
-		compatible = "renesas,r8a77950-rcar-usb2-clock-sel",
+		compatible = "renesas,r8a7795-rcar-usb2-clock-sel",
 			     "renesas,rcar-gen3-usb2-clock-sel";
 		reg = <0 0xe6590630 0 0x02>;
 		clocks = <&cpg CPG_MOD 703>, <&usb_extal>, <&usb_xtal>;

Documentation/devicetree/bindings/reset/brcm,brcmstb-reset.txt

@@ -22,6 +22,6 @@ Example:
 	};
 
 	&ethernet_switch {
-		resets = <&reset>;
+		resets = <&reset 26>;
 		reset-names = "switch";
 	};

Documentation/devicetree/bindings/sound/mt8183-mt6358-ts3a227-max98357.txt

@@ -2,9 +2,11 @@ MT8183 with MT6358, TS3A227 and MAX98357 CODECS
 
 Required properties:
 - compatible : "mediatek,mt8183_mt6358_ts3a227_max98357"
-- mediatek,headset-codec: the phandles of ts3a227 codecs
 - mediatek,platform: the phandle of MT8183 ASoC platform
 
+Optional properties:
+- mediatek,headset-codec: the phandles of ts3a227 codecs
+
 Example:
 
 	sound {

Documentation/networking/j1939.rst

@@ -339,7 +339,7 @@ To claim an address following code example can be used:
 			.pgn = J1939_PGN_ADDRESS_CLAIMED,
 			.pgn_mask = J1939_PGN_PDU1_MAX,
 		}, {
-			.pgn = J1939_PGN_ADDRESS_REQUEST,
+			.pgn = J1939_PGN_REQUEST,
 			.pgn_mask = J1939_PGN_PDU1_MAX,
 		}, {
 			.pgn = J1939_PGN_ADDRESS_COMMANDED,

Documentation/scsi/smartpqi.txt

@@ -29,7 +29,7 @@ smartpqi specific entries in /sys
   smartpqi host attributes:
   -------------------------
   /sys/class/scsi_host/host*/rescan
-  /sys/class/scsi_host/host*/version
+  /sys/class/scsi_host/host*/driver_version
 
   The host rescan attribute is a write only attribute. Writing to this
   attribute will trigger the driver to scan for new, changed, or removed

MAINTAINERS

@@ -6973,6 +6973,7 @@ L:	linux-acpi@vger.kernel.org
 S:	Maintained
 F:	Documentation/firmware-guide/acpi/gpio-properties.rst
 F:	drivers/gpio/gpiolib-acpi.c
+F:	drivers/gpio/gpiolib-acpi.h
 GPIO IR Transmitter
 M:	Sean Young <sean@mess.org>

Makefile

 # SPDX-License-Identifier: GPL-2.0
 VERSION = 5
 PATCHLEVEL = 4
-SUBLEVEL = 8
+SUBLEVEL = 13
 EXTRAVERSION =
 NAME = Kleptomaniac Octopus
 

arch/arm/Kconfig

@@ -73,6 +73,7 @@ config ARM
 	select HAVE_ARM_SMCCC if CPU_V7
 	select HAVE_EBPF_JIT if !CPU_ENDIAN_BE32
 	select HAVE_CONTEXT_TRACKING
+	select HAVE_COPY_THREAD_TLS
 	select HAVE_C_RECORDMCOUNT
 	select HAVE_DEBUG_KMEMLEAK
 	select HAVE_DMA_CONTIGUOUS if MMU

arch/arm/boot/dts/am335x-sancloud-bbe.dts

@@ -108,7 +108,7 @@ ethphy0: ethernet-phy@0 {
 
 &cpsw_emac0 {
 	phy-handle = <&ethphy0>;
-	phy-mode = "rgmii-txid";
+	phy-mode = "rgmii-id";
 };
 
 &i2c0 {

arch/arm/boot/dts/am437x-gp-evm.dts

@@ -86,7 +86,7 @@ &gpio4 3 GPIO_ACTIVE_HIGH /* Bank4, pin3 */
 		};
 
 	lcd0: display {
-		compatible = "osddisplays,osd057T0559-34ts", "panel-dpi";
+		compatible = "osddisplays,osd070t1718-19ts", "panel-dpi";
 		label = "lcd";
 
 		backlight = <&lcd_bl>;

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -42,7 +42,7 @@ vbat: fixedregulator0 {
 	};
 
 	lcd0: display {
-		compatible = "osddisplays,osd057T0559-34ts", "panel-dpi";
+		compatible = "osddisplays,osd070t1718-19ts", "panel-dpi";
 		label = "lcd";
 
 		backlight = <&lcd_bl>;

arch/arm/boot/dts/bcm-cygnus.dtsi

@@ -174,8 +174,8 @@ gpio_crmu: gpio@3024800 {
 		mdio: mdio@18002000 {
 			compatible = "brcm,iproc-mdio";
 			reg = <0x18002000 0x8>;
-			#size-cells = <1>;
-			#address-cells = <0>;
+			#size-cells = <0>;
+			#address-cells = <1>;
 			status = "disabled";
 
 			gphy0: ethernet-phy@0 {

arch/arm/boot/dts/bcm283x.dtsi

@@ -40,7 +40,7 @@ cpu_thermal: cpu-thermal {
 
 			trips {
 				cpu-crit {
-					temperature	= <80000>;
+					temperature	= <90000>;
 					hysteresis	= <0>;
 					type		= "critical";
 				};

arch/arm/boot/dts/bcm5301x.dtsi

@@ -353,8 +353,8 @@ gmac3: ethernet@27000 {
 	mdio: mdio@18003000 {
 		compatible = "brcm,iproc-mdio";
 		reg = <0x18003000 0x8>;
-		#size-cells = <1>;
-		#address-cells = <0>;
+		#size-cells = <0>;
+		#address-cells = <1>;
 	};
 
 	mdio-bus-mux@18003000 {

arch/arm/boot/dts/imx6ul-14x14-evk.dtsi

@@ -215,7 +215,7 @@ &qspi {
 	flash0: n25q256a@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "micron,n25q256a";
+		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
 		spi-tx-bus-width = <4>;

arch/arm/configs/exynos_defconfig

@@ -348,6 +348,7 @@ CONFIG_PRINTK_TIME=y
 CONFIG_DYNAMIC_DEBUG=y
 CONFIG_DEBUG_INFO=y
 CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_SOFTLOCKUP_DETECTOR=y
 # CONFIG_DETECT_HUNG_TASK is not set